PGXD1 Bodypack:

• Rugged, compact bodypack with belt clip and instrument cable
• 20 Hz 20 kHz frequency range captures every nuance of your tone
• Power, mute, and battery status LED
• Up to 10 hours of continuous use from 2 AA batteries
• 200ft (60m) operating range
• 26 dB of continuously adjustable gain to match variable input levels

PGXD4 Wireless Receiver:

• 24-bit / 48 kHz digital technology for incredibly accurate sound
• Automatic frequency selection locates a clear channel instantly
• One-touch sync automatically syncs the transmitter and receiver
• Rugged construction for reliable performance show after show
• True digital diversity for rock-solid wireless signal reliability
• Up to 10 compatible channels per frequency band
• ¼" and XLR audio output

• Operating Range: 200ft (60m) under typical conditions.
  • Note: actual range depends on RF signal absorption, reflection, and interference.
• RF Carrier Range:
  • X8: 902 928 MHz
  • X8A: 915 928 MHz
  • X8B: 902 907.5 MHz
  • 915 928 MHz (Note: varies by region)
• Audio Frequency Response (± 2 dB): 20-20,000 MHz
• System Gain:
  • PGXD1:
    • -54.5 dBV/Pa at -10dB gain setting, with SM58 catridge, XLR output
• Total Harmonic Distortion: <0.02%, A-weighted, typical (Ref. 1 kHz, 6dB below input clip)
• Dynamic Range: >108 dB A-weighted
• Operating Temperature Range: 0°F (-18°C) to +122°F (+50°C).
  • Note: battery characteristics may limit this range.

PGXD1 Bodypack:

• Audio Input Level: +10 dBV maximum, at minimum gain setting
• -16 dBVmaximum, at maximum gain setting
• Gain Adjustment Range: 26 dB
• Input Impedance: 1 M Ohm
• RF Output Level: 10 mW maximum (dependent on applicable country regulations)
• Dimensions (HxWxD): 4.25" x 2.50" x 0.75" (108 x 64 x 19mm)
• Weight: 4.5 oz (128 g) without batteries
• Housing: Molded polycarbonate case
• Power Requirements: 2 AA size
• Battery Life: Up to 10 hours

Shure PGXD4 Wireless Receiver:

• Dimensions (HxWxD): 1.6" x 7.125" x 4.1" (40 x 181 x 104mm)
• Weight: 10.2 oz (289 g)
• Housing: ABS
• Audio Output Level (ref. ± 38 kHz deviation, 1 kHz tone):
  • XLR connector (into 3,000-Ohm load): -2.5 dBV
  • 1/4" connector (into 10,000-Ohm load): +10 dBV
• Impedance:
  • XLR: 50 Ohms
  • ¼": 50 Ohms
• Sensitivity: -102 dBm @ 10-5 BER
• Image Rejection: > 70 dB, typical
• XLR output (impedance balanced):
  • Pin 1: Ground (cable shield)
  • Pin 2: Audio
  • Pin 3: No Audio
• Audio LED:
  • Red: 2 dB below clip
  • Amber: 12 dB below clip
  • Green: 50 dBbelow clip
  • Power Requirements: 12-18 VDC at150 mA, supplied by external power supply
  • Pin Assignments:
    • XLR: 1=ground, 2=hot, 3=cold
    • ¼" (6.35mm) TRS: Tip=audio, Ring=no audio, Sleeve=ground

• PGXD4 wireless receiver
• PGXD1 bodypack transmitter
• WA302 instrument cable
• Power supply
• 2 AA batteries
• Carrying case
• User guide