ProX XT-BLOCK-MK2 Ground Support Sleeve Block for F34

ProX XT-BLOCK-MK2: Rapid, Rock-Solid Lifts for F34 12 in Truss

Built for fast, safe rigging. The ProX XT-BLOCK-MK2 sleeve block locks onto F34 12 in truss to raise and lower roof grids and front-truss lines with tight, repeatable alignment. Manufactured from EN-AWT6 6082 aluminum with TUV-certified welding, it uses tolerance-free standard conical connectors and includes tapered shear pins with clips for secure, play-free seating.

Field-ready compatibility. Four connecting sides, a 1.75 in top loop, and F34 geometry (2 in / 50 mm main tube, 2 mm wall, 0.75 in / 20 mm braces) make this a go-to choice for Chicago DJs, clubs, outdoor productions, and permanent installs that demand speed and consistency.

• UPC: 019372406358

Real-World Applications and Roles

• Ground-support roof legs for mobile DJ rigs and festival pop-ups
• Nightclub grid service lifts with precise up/down control
• Install and rental workflows needing quick, repeatable alignment

Where the XT-BLOCK-MK2 Sleeve Block Excels

• Speed on show days: Conical receivers and tapered pins seat fast for tight turnarounds.
• Stable alignment: Tolerance-free interfaces reduce rattle and drift during lifts.
• F34 ecosystem fit: Standard connector system plays well with common corners and spans.
• Road-worthy build: EN-AWT6 6082 aluminum and TUV-certified welds handle repeated cycles.
• DJ/event utility: Ideal for Chicago clubs and mobile stages where quiet, clean seating matters.

Construction & Interface Highlights

• Material: EN-AWT6 6082 aluminum for high strength-to-weight performance.
• Welding: TUV-certified aluminum welding for verified quality and consistency.
• Connections: Four-side F34 interface using standard conical connectors.
• Pin set: Includes tapered shear pins with clips for secure, play-free seating.
• Top loop: 1.75 in loop sized for common lifting hardware (verify system limits).

Safety, Loads & Pre-Lift Checks

• Know your load: Confirm total system weight using the official F34 loading chart before any lift.
• Pin discipline: Insert all pins fully, secure clips, and re-verify under initial tension.
• Inspection: Check cones, cups, welds, and truss ends for wear or deformation before deployment.

Crew Handling & Logistics

• Packed footprint & weight: 18.50 in H x 22.50 in W x 22.50 in L — 77.30 lb
• Shipping carton: 20.00 in H x 24.00 in W x 24.00 in L — 80.00 lb; suggested method: Parcel

How to Deploy the ProX XT-BLOCK-MK2

1. Stage the bases: Position ground-support hardware and ensure a level footprint.
2. Seat the block: Align with F34 ends and engage the conical receivers.
3. Lock the pins: Insert tapered pins fully and secure with clips; verify zero play.
4. Attach lift: Connect an approved lifting device to the 1.75 in top loop within rated limits.
5. Build the grid: Add corners and spans; confirm symmetry and bracing before tension.
6. Test lift: Take up slack slowly, re-check connections, then proceed to working height.

Why Choose AVMaxx for XT-BLOCK-MK2

• Application authority: Guidance grounded in real DJ/event deployments and club installs.
• Data integrity: Only the current manufacturer details you provide—no assumptions.
• Chicago DJ focus: Practical tips for fast resets between sets and clean, quiet lifts.

Frequently Asked Questions — ProX XT-BLOCK-MK2

Tell us your span, height, and hoist plan — we will help you configure a fast, safe XT-BLOCK-MK2 deployment for your next show.