Black-on-Black Road Armor for Pioneer XDJ-XZ — ProX XS-XDJXZWBL with 1U Rack & Wheels
Built specifically around the Pioneer XDJ-XZ, the ProX XS-XDJXZWBL is an ATA-300 flight case that travels hard and sets up fast. Its Honeycomb Digital™ laminate over 3/8" plywood shrugs off everyday scrapes while the black-on-black finish keeps the booth looking sharp. Inside, a high-density foam bed supports the controller; below, a bottom 1U / 19" rack space integrates wireless, power, or processing so the rig rolls in as one unit.
Hardware includes ProX branded recessed butterfly latches (padlock-ready), spring-action recessed handles, heavy steel ball corners, and dual-anchor rivets. Mobility is handled by two low-profile rubber wheels and four industrial rubber feet. The removable front panel opens instant access to front I/O and the rack bay, with extra room at the rear/underneath for cables and small accessories.
- Real-World Applications and Sound Roles: Chicago ballroom weddings, club takeovers, corporate AV, campus shows, production rentals, and mobile DJ residencies.
Where the ProX XS-XDJXZWBL Excels
- Controller-Specific Protection: Foam-supported fit for the Pioneer XDJ-XZ stabilizes the deck in transit.
- Integrated 1U Bay: Bottom 1U rack space mounts receivers or power so your workflow stays consolidated.
- Fast Booth Access: Removable front panel exposes headphone/mic jacks and front inputs immediately.
- Road-Ready Shell: 3/8" plywood, steel ball corners, and dual-anchor rivets handle daily loading.
- Clean, Durable Finish: Honeycomb Digital™ laminate hides minor wear; black-on-black looks pro on camera.
- Easy Mobility: Low-profile wheels and recessed handles speed hotel and club turns.
- Stable Footing: Industrial rubber feet keep the case planted on risers and carpet.
- Secure Closure: Recessed butterfly twist-lock latches are padlock-ready for transport security.
- Chicago DJ Focus: Optimized for quick ballroom turnovers and tight booth changeovers.
Construction & Hardware Details
The XS-XDJXZWBL is a ProX ATA-300 flight/road case using 3/8" laminated plywood aligned by aluminum tongue-and-groove for a tight seal. Corners are protected by heavy steel balls, panels are fastened with dual-anchor rivets, and all touch points are recessed to avoid snags during load-ins.
Finish, Fit & Everyday Protection
The Honeycomb Digital™ hex-grid laminate (black on black) delivers a modern aesthetic and helps resist minor to mild scratches. Internally, high-density foam supports the XDJ-XZ while leaving space at the rear and underneath for cable coils and essentials.
Rack Integration & Cable Management
A bottom 1U rack space (rails included; front or rear mount) keeps your wireless, power, or processing hardware attached to the same footprint. The removable front panel provides clear reach to the rack bay and the controller’s front-panel connections for quick patching.
Mobility & Dimensions
With two low-profile rubber wheels, four industrial feet, and balanced recessed handles, the case rolls easily through hotels and clubs. Exterior size is 9.50" H × 23.00" W × 37.50" L at 39.00 lb; shipping is 11.50" H × 25.50" W × 39.00" L at 46.00 lb.
How to Deploy the ProX XS-XDJXZWBL in the Field
Place the case on a stable table or riser. Release the recessed butterfly latches and remove the front access panel. Slide the XDJ-XZ into the foam cradle if not already housed. Populate the 1U rack bay with your receiver or power unit (front or rear rails) and route I/O to the rear space for a clean booth. After the set, stow cables beneath/behind the controller, re-install the panel, lock the latches, tilt to the low-profile wheels, and roll out.
One case, one footprint—roll in, wire clean, and perform with a Chicago-ready workflow.
Why Choose the ProX XS-XDJXZWBL from AVMaxx
We align every detail with manufacturer data and on-site deployment know-how. This case’s 1U bay, front access, and black-on-black Honeycomb Digital™ finish match how XDJ-XZ users actually work—from ballroom timelines to club changeovers.
AVMaxx is your partner for ProX solutions—field-aware recommendations, dependable support, and builds that help Chicago DJs and event pros perform with confidence.
Frequently Asked Questions — ProX XS-XDJXZWBL
Is the XS-XDJXZWBL made for the Pioneer XDJ-XZ?
Yes. It is designed for the Pioneer XDJ-XZ and includes a high-density foam interior for support.
Does it include rack space for accessories?
Yes. There is a bottom 1U / 19" rack space with rails that can mount from the front or the rear.
What materials and hardware does the case use?
3/8" laminated plywood with Honeycomb Digital™ finish, steel ball corners, recessed butterfly latches, spring-action recessed handles, and dual-anchor rivets.
How portable is it for frequent gigs?
It features two low-profile rubber wheels and four industrial rubber feet for stable staging and smooth rolling.
DJ-use: Can I patch quickly during a club takeover?
Yes. The removable front panel exposes the controller’s front I/O and the 1U rack bay for fast changeovers.
Want help outfitting the 1U bay or cabling the XDJ-XZ for your venue? Share your rig details and we’ll tune a clean, performance-ready setup.
