ProX X-DDJFLX4LTBL: All-Black Laptop-Shelf Case for DDJ-FLX4 / DDJ-400 / DDJ-SB3
Built for compact, laptop-over-controller rigs with a stealth look. The X-DDJFLX4LTBL wraps your Pioneer controller in an ATA-300 style shell made from 3/8-inch plywood, reinforced steel ball corners, recessed butterfly latches, and spring-loaded recessed handles. Its Black on Black Honeycomb Digital exterior keeps reflections down and disguises scuffs so the case stays presentable in clubs, pop-ups, and rentals.
Workflow-first details keep setups fast and wiring clean. The smooth sliding laptop shelf sits directly above the controller and includes a cable-thru channel. Inside, high-density foam cradles the unit; a removable front panel exposes headphone, mic, and front-edge controls; and a rear accessory bay stows small cables. You get useful clearances—about 3 inches of extra lid height and about 3 inches of cable space—plus a console cavity around 3.50" H x 10.50" W x 19.00" L sized for DDJ-FLX4, DDJ-400, and DDJ-SB3. CNC-cut panels close square so the lid seals tight and stacks neatly on carts and shelves.
- Real-World Applications & Use Cases:
- Mobile DJ sets needing a tidy laptop-over-controller layout and quick changeovers.
- Club booths where a dark, low-glare finish and front-panel access are essential.
- Livestream or campus events that benefit from integrated laptop placement and clean cabling.
- Rental fleets requiring a repeatable fit and durable road hardware.
Where This Case Excels
- Stealth presentation: Black hardware and Black on Black Honeycomb Digital finish blend into modern booths.
- Integrated laptop shelf: Sliding tray with cable-thru keeps screens close and wires out of sight.
- Controller fit dialed in: Sized for DDJ-FLX4, DDJ-400, and DDJ-SB3 with a console space around 3.50" x 10.50" x 19.00".
- Fast front access: Removable panel exposes headphone, mic, and front-edge controls instantly.
- Tidy routing: Rear accessory bay plus about 3" extra cable space support short, strain-relieved runs.
- Road durability: 3/8-inch plywood, steel ball corners, recessed latches, and dual-rivet reinforcement stand up to weekly gigs.
- Stable staging: Industrial rubber feet help the base stay planted on tables and risers.
- Square packs: CNC-cut panels close flush for rattle-free transport and clean stacking.
- Practical safety: Do not move the case with the shelf open or devices on the shelf; do not store a laptop inside when closed.
Chassis & Materials of the X-DDJFLX4LTBL
Ready for nightly travel with a stealth aesthetic. The X-DDJFLX4LTBL is built on an ATA-300 style frame using rugged 3/8-inch plywood. Reinforced steel ball corners, dual anchor rivets, and tight-fitting panels create a rigid enclosure that shrugs off bumps and stacks square on carts and shelves. The all-black hardware keeps the look cohesive from booth to truck pack.
All-Black Honeycomb Digital Exterior & Finish
Low-glare presentation that hides wear. The Black on Black Honeycomb Digital exterior uses a textured laminate that helps mask minor scuffs and maintains a clean look under club lighting. With black hardware throughout, the case blends into modern DJ furniture and stage backlines while still reading premium up close.
Sliding Laptop Shelf — Glide, Cable-Thru & Safety
Laptop-over-controller without cable clutter. The integrated sliding shelf positions your screen directly above the controller for compact, ergonomic setups. A built-in cable-thru keeps power and USB lines tidy. For device safety: do not leave laptops or other gear inside the closed case, and never move or transport the case with the shelf open or with devices sitting on the tray.
Interior Fit, Foam Protection & Rear Accessory Bay
Support where it protects faders, pads, and jacks. High-density foam cradles the controller to control shock during travel, while a rear accessory area under the unit stores short cables and essentials. Useful extra clearances include about 3 inches of additional lid height and about 3 inches of cable space to prevent pressure on knobs and connectors.
Front Panel Access & Cable Management Workflow
Patch fast, keep lines short. The removable front panel exposes front-edge controls along with headphone and mic jacks for quick patching. Pair this with the shelf cable-thru to run short, strain-relieved leads that stay out of sight, reduce snags during changeovers, and let you close the lid cleanly after the set.
Road Hardware, Handling & Security
Low-profile parts that survive real-world use. Recessed butterfly latches lock down the lid and sit flush to avoid catches. Spring-loaded recessed handles center the lift for balanced carries, and industrial rubber feet give the base stable footing on risers and tables. Padlock the latches between shows for added peace of mind.
CNC Manufacturing, Warranty & Eco Materials
Consistency case after case. CNC fabrication holds tolerances so panels meet flush and hardware lines up every time. The X-DDJFLX4LTBL includes the ProX Limited Lifetime Warranty, and the durable hard rubber foam inside uses approximately 70% recycled content (most from recycled plastic bottles, with the remainder from recycled post-industrial material).
Controller Compatibility & Key Dimensions
Dialed for popular Pioneer controllers. Sized for DDJ-FLX4, DDJ-400, and DDJ-SB3, with an interior console space around 3.50" H × 10.50" W × 19.00" L. The sliding laptop shelf area is approximately 21.5" × 11.5". Exterior size is roughly 10.00" H × 17.00" W × 22.50" L at about 20.0 lb. Shipping carton is about 11.00" × 18.00" × 23.00" at around 22.0 lb (suggested method: parcel). Use the extra 3" lid and 3" cable clearances to avoid jack and knob pressure when packing.
How to Deploy the X-DDJFLX4LTBL in the Field
Stealth look, fast setup. Use this sequence to stage a clean laptop-over-controller rig for DDJ-FLX4, DDJ-400, or DDJ-SB3—tight wiring, secure handling, and repeatable results.
1) Fit and Foam Dial-In
- Seat the controller: Place it flat in the console cavity and check clearance around pads, knobs, and the rear I/O.
- Support, not pressure: The high-density foam should contact the chassis—not the controls. Add thin shims only if you want a firmer side hold.
- Lid trial: Close and latch the lid once to confirm nothing touches faders or encoders.
2) Laptop Shelf Setup (Safety First)
- Extend and center: Slide the shelf out fully and center the laptop for balance.
- Use the cable-thru: Route USB and power through the pass-through to keep the work surface clear.
- Important: Do not store a laptop inside the closed case. Never move or transport the case with the shelf open or with devices sitting on the shelf.
3) Cable Path & Front Access
- Rear run: Use the rear accessory bay to dress short, strain-relieved loops for power and audio.
- Front panel off: Remove the front panel to reach headphone, mic, and front-edge controls without lifting the unit.
- Label both ends: Mark USB and main outs for fast changeovers in shared booths.
4) Booth Placement & Stability
- Solid surface: Set the base on a stable table or riser; the rubber feet keep the case planted.
- Store the lid: Lift the lid straight up after unlatching and place it away from traffic and drinks.
- Low-glare advantage: The black finish keeps reflections down—use minimal top lighting to maintain visibility without glare.
5) Power-On & Gain Structure
- Order of operations: Connect USB/audio ? power laptop/controller ? bring PA up last.
- Headroom: Trim channels so peaks sit just below 0 on the controller meter; leave margin at the PA.
6) Strike, Latch, and Secure
- Pack clean: Coil and stow cables in the rear bay; reinstall the front panel.
- Square the close: Seat the lid fully and latch opposite corners first for an even seal.
- Lock it: Use small padlocks in the recessed latches if the case will sit unattended.
7) Changeovers & Rental Prep
- Pre-wired loom: Build a short USB/power/audio loom sized to the pass-through for one-minute swaps.
- Checklist card: Tape a small card inside the lid with controller model, cable inventory, and shelf safety note.
Follow this flow and your black-on-black laptop shelf rig loads in fast, looks clean on camera, and packs down without surprises—night after night.
Related Gear & Compatible Options
Match finishes, pair the right controller, and add accessory protection. These AVMaxx links help you complete a clean, laptop-over-controller rig.
Why Choose This Case from AVMaxx
We recommend gear that runs clean in real booths and survives weekly load-ins. The X-DDJFLX4LTBL adds a stealth, all-black finish to a Gig-Ready road chassis, with a sliding laptop shelf, removable front panel, and a tidy rear accessory bay. High-density foam protects the controller, extra lid and cable clearance prevent pressure on jacks, and low-profile hardware keeps snags to a minimum. Our guidance is built strictly on ProX details and field workflow: short cable runs through the shelf pass-through, front-panel patching for quick changeovers, and square, rattle-free closes thanks to CNC-cut panels. If you want a compact laptop-over-controller rig that looks pro on camera and travels hard, this is the case we stand behind.
Frequently Asked Questions — ProX X-DDJFLX4LTBL Laptop-Shelf Controller Case
Which controllers fit this case?
It is sized for Pioneer DJ DDJ-FLX4, DDJ-400, and DDJ-SB3. Compare to the console space of about 3.50" H x 10.50" W x 19.00" L to confirm.
Can I perform with the controller sitting in the base?
Yes. The removable front panel exposes front-edge controls and headphone or mic jacks so you can patch and play without lifting the unit.
Is the laptop shelf safe to travel with when open?
No. Do not move or transport the case with the shelf open or with a device on the shelf. Do not store a laptop inside the closed case.
Is there room for cables and small accessories?
Yes. There is a rear accessory bay under the controller plus about 3" of additional cable space. Keep loops short and strain-relieved.
How durable is the all-black exterior?
The black Honeycomb Digital laminate is a textured surface that helps resist minor scuffs and keeps reflections low in booths and on camera.
What are the exterior and shipping dimensions?
Approx exterior: 10.00" H x 17.00" W x 22.50" L at about 20 lb. Shipping carton: 11.00" x 18.00" x 23.00" at about 22 lb (suggested: parcel).
What hardware and protections are included?
Recessed butterfly latches, spring-loaded recessed handles, steel ball corners, high-density foam, and industrial rubber feet, plus a removable front panel.
Need fit confirmation or cabling advice for your exact setup? Tell us your controller and we will verify clearances and a clean routing plan before you buy.
